6. Putting them together: Making the diskette(s)

6.1. Transferring the kernel with LILO

The first thing you must do is create a small configuration file for LILO. It should look like this:

boot =/dev/fd0 install =/boot/boot.b map =/boot/map read-write backup =/dev/null compact image = KERNEL label = Bootdisk root =/dev/fd0

For an explanation of these parameters, see LILO's user documentation. You will probably also want to add an append=... line to this file from your hard disk's /etc/lilo.conf file.

Save this file as bdlilo.conf.

You now have to create a small filesystem, which we shall call a kernel filesystem, to distinguish it from the root filesystem.

First, figure out how large the filesystem should be. Take the size of your kernel in blocks (the size shown by ``ls -s KERNEL'') and add 50. Fifty blocks is approximately the space needed for inodes plus other files. You can calculate this number exactly if you want to, or just use 50. If you're creating a two-disk set, you may as well overestimate the space since the first disk is only used for the kernel anyway. Call this number KERNEL_BLOCKS.

Put a floppy diskette in the drive (for simplicity we'll assume /dev/fd0) and create an ext2 kernel filesystem on it:

mke2fs -i 8192 -m 0 /dev/fd0 KERNEL_BLOCKS

The ``-i 8192'' specifies one inode per 8192 bytes. Next, mount the filesystem, remove the lost+found directory, and create dev and boot directories for LILO:

mount /dev/fd0 /mnt rm -rf /mnt/lost+found mkdir /mnt/{boot,dev}

Next, create devices /dev/null and /dev/fd0. Instead of looking up the device numbers, you can just copy them from your hard disk using -R:

cp -R /dev/{null,fd0} /mnt/dev

LILO needs a copy of its boot loader, boot.b, which you can take from your hard disk. It is usually kept in the /boot directory.

cp /boot/boot.b /mnt/boot

Finally, copy in the LILO configuration file you created in the last section, along with your kernel. Both can be put in the root directory:

cp bdlilo.conf KERNEL /mnt

Everything LILO needs is now on the kernel filesystem, so you are ready to run it. LILO's -r flag is used for installing the boot loader on some other root:

lilo -v -C bdlilo.conf -r /mnt

LILO should run without error, after which the kernel filesystem should look something like this:

total 361 1 –rw–r––r–– 1 root root 176 Jan 10 07:22 bdlilo.conf 1 drwxr–xr–x 2 root root 1024 Jan 10 07:23 boot/ 1 drwxr–xr–x 2 root root 1024 Jan 10 07:22 dev/ 358 –rw–r––r–– 1 root root 362707 Jan 10 07:23 vmlinuz boot: total 8 4 –rw–r––r–– 1 root root 3708 Jan 10 07:22 boot.b 4 –rw––––––– 1 root root 3584 Jan 10 07:23 map dev: total 0 0 brw–r––––– 1 root root 2, 0 Jan 10 07:22 fd0 0 crw–r––r–– 1 root root 1, 3 Jan 10 07:22 null

Do not worry if the file sizes are slightly different from yours.

Now leave the diskette in the drive and go to Section 6.3.

6.2. Transferring the kernel without LILO

If you are not using LILO, transfer the kernel to the bootdisk with dd:

% dd if=KERNEL of=/dev/fd0 bs=1k 353+1 records in 353+1 records out

In this example, dd wrote 353 complete records + 1 partial record, so the kernel occupies the first 354 blocks of the diskette. Call this number KERNEL_BLOCKS and remember it for use in the next section.

Finally, set the root device to be the diskette itself, then set the root to be loaded read/write:

rdev /dev/fd0 /dev/fd0 rdev -R /dev/fd0 0

Be careful to use a capital -R in the second rdev command.

6.3. Setting the ramdisk word

Inside the kernel image is the ramdisk word that specifies where the root filesystem is to be found, along with other options. The word can be accessed and set via the rdev command, and its contents are interpreted as follows:

If bit 15 is set, on boot-up you will be prompted to place a new floppy diskette in the drive. This is necessary for a two-disk boot set.

There are two cases, depending on whether you are building a single boot/root diskette or a double ``boot+root'' diskette set.

1. If you are building a single disk, the compressed root filesystem will be placed right after the kernel, so the offset will be the first free block (which should be the same as KERNEL_BLOCKS). Bit 14 will be set to 1, and bit 15 will be zero. For example, say you're building a single disk and the root filesystem will begin at block 253 (decimal). The ramdisk word value should be 253 (decimal) with bit 14 set to 1 and bit 15 set to 0. To calculate the value you can simply add the decimal values. 253 + (2^14) = 253 + 16384 = 16637. If you don't quite understand where this number comes from, plug it into a scientific calculator and convert it to binary,

2. If you are building a two-disk set, the root filesystem will begin at block zero of the second disk, so the offset will be zero. Bit 14 will be set to 1 and bit 15 will be 1. The decimal value will be 2^14 + 2^15 = 49152 in this case.

After carefully calculating the value for the ramdisk word, set it with rdev -r. Be sure to use the decimal value. If you used LILO, the argument to rdev here should be the mounted kernel path, e.g. /mnt/vmlinuz; if you copied the kernel with dd, instead use the floppy device name (e.g., /dev/fd0).

rdev -r KERNEL_OR_FLOPPY_DRIVE VALUE

If you used LILO, unmount the diskette now.

6.4. Transferring the root filesystem

The last step is to transfer the root filesystem.

• If the root filesystem will be placed on the same disk as the kernel, transfer it using dd with the seek option, which specifies how many blocks to skip:

  dd if=rootfs.gz of=/dev/fd0 bs=1k seek=KERNEL_BLOCKS

• If the root filesystem will be placed on a second disk, remove the first diskette, put the second diskette in the drive, then transfer the root filesystem to it:

  dd if=rootfs.gz of=/dev/fd0 bs=1k

Congratulations, you are done!